| home | products | checkout | contact  
  PRODUCTS      



Shopping cart  Shopping cart
0 Product(s) in cart
Total $0.00
» Checkout

 
Holochess Knob Set

 

1 set of 10 Holochess Table Knobs machined from 6061 Aluminum. Each has a 6mm hole in the back side for mounting on a switch.

 

 

Price: $90.00

Fringe Dress Brass Lapel Pin

 


Polished brass Fringe Division pins seen on dress uniforms in the Season 4 episode "The Consultant" during the funeral. 1.025" tall with a single pin clasp on the back.

Price shown here includes postage.

Patch not included, shown for scale only
 

 

Price: $15.00

Fett1

This is a Boba Fett jetpack greeblie machined to match the found part, including the important correct pitch on the knurled end. The tip does not unscrew like the found part, but displays the same.
 

Price: $35.00

FettRocket

Boba Fett replica rocket, complete with accurate copper tip. This rocket is based off actual measurements of a real piece and comes in 3 pieces, which screw together. This is a new version for 2018, and is the most accurate replica ever made.

Price includes shipping to domestic U.S. addresses. Please select shipping location below.
 

Price: $250.00

R2-D2 Dome Bullets
1 of 2

R2-D2 Dome Alignment Bullet set of 6. These are threaded 10-32 x .25" diameter, giving you more precise adjustment than 10-24 threads. Drill your dome ring to just slip over the bullets, add a slight chamfer, and these will enable quick and easier alignment and removal of dome. Your current screws may be 10-24, so be sure and check.

There is an option to also order stainless screws and nuts that fit the Rockler bearings and dome bullets.

UK / EU Resident VAT Disclosure: https://www.newwookiee.com/vat.asp

Screws/Nuts
No Screws
6 screws 18 nuts (+$5.00)
Price: $34.00

R2-D2 Dome Topper
1 of 5

This is a replica of one of the real R2 dome toppers. It happens to be the one I took photos of when I was around this particular R2 when Don Bies had it at Steve Sansweet's Rancho Obi-Wan for a photo shoot years ago. Of all the toppers I've seen, it's the most interesting since it has a beveled edge instead of just being rounded over.

It's aluminum and made in two pieces, so finishing is easy. It fits into the hole inside Daren's alum dome, and is held with an included 1/4" ss washer and ss 1/4-28 nut.

Price: $28.00

R2-D2 CS:R
1 of 2

These skins have been updated to make them easier to prepare, will show which panels always get removed, and include a coin return flat-pack, which you can use to assemble your own coin returns that can glue to the coin return faces, which are also provided as part of the rolled outside skins.

R2-D2 CS:R Aluminum Skin. This skin is very nicely laser cut, deburred and rolled in 4 pieces. Front and back, inside and outside pieces. The skin will ship in a custom foam cradle and custom box to continental US addresses via UPS ground service, and Priority Mail for all locations outside the U.S., and other U.S. destinations.

Please enter your Astromech display name in the comments.

If you use sbcglobal for email, you will probably not receive communications from the store.

I'll apologize in advance for the cost to ship outside the U.S. It keeps rising.

Price: $355.00

R2-D2 CS:Rh
1 of 2

These skins have been updated to make them easier to prepare, will show which panels always get removed, and include a coin return flat-pack, which you can use to assemble your own coin returns that can glue to the coin return faces, which are also provided as part of the rolled outside skins.

R2-D2 CS:Rh (Holmes Frame Specific Aluminum Skin). This skin is very nicely laser cut, deburred and rolled in 4 pieces. Front and back, inside and outside pieces. The skin will ship in a custom foam cradle and custom box to continental US addresses via UPS ground service, and Priority Mail for all locations outside the U.S., and other U.S. destinations.
 
Please enter your Astromech display name in the comments.

If you use sbcglobal for email, you will not receive communications from the store.

 

Price: $355.00

R2-D2 CS:L
1 of 2

R2-D2 CS:L Aluminum Skin. This skin is very nicely laser cut and rolled in 4 pieces. The rolling is complete, and will roll all the small panels as well. Front and back, inside and outside pieces. The skin will ship in a custom foam cradle and custom box to continental US addresses via UPS ground service, and Priority Mail for all locations outside the U.S., and other U.S. destinations.

Please enter your Astromech display name in the comments.

If you use sbcglobal for email, you will not receive communications from the store.

 
 
Price: $335.00

R2 Skin Snaps

Skin Snaps. Set of 6 with mounting screws.

Price: $57.00

R2-D2 Curved Rear Logic Display
1 of 2

These are out of stock and at the moment I plan to do one final run of these during 2023. 

R2-D2 Curved Rear Logic Display. Includes aluminum outer bezel, aluminum inner bezel, both with matching curve to replica R2's display fiber mount. Clear overlay acrylic and the accurate wonky fiber location. This kit requires the curved bezel electronics from Joymonkey.

 

 

Price: $185.00
Out of Stock

R2-D2 Flat Rear Logic Display Bezel

R2-D2 Aluminum Flat Rear Logic Display bezel. No mounting hardware is included for the bezel. No mounting hardware is included for the electronics. These aren't standardized, and generally are included with your electonics. The bezel is tapped 4-40 for them.

 

 

Price: $170.00

R2-D2 Front Logic Display Bezels

R2-D2 Aluminum Front Logic Display bezels (pair). No mounting hardware is included for the bezel. A set of 4-40 screws are included to mount your electronics boards.

Price: $120.00

R2-D2 HP Servo Mount

This is a servo mount, mount hardware, and servo screws. This mount fits both my HP mounting rings, as well as the BobC rings.

 

 

Price: $35.00

R2-D2 Hub Adapter

This adapter fits the Granite Earth dome drive and allows you to install Pixelfiend's geared dome setup. It has 3 screws for attaching to the motor shaft after you cut it to length. It's best if you can file flats onto the shaft for each of the fixing screws. If you have a dome plate right on top of the gear set, you will want to countersink 82 degrees for flathead screws. The adapter comes with both capscrews and flathead screws.

When you order your gearset from Pixelfiend, tell him you are using this adapter and he will drill the proper holes in the pinion.

Price: $30.00

« Previous | 1 | 2 | »

Skytower Props, Inc.
101 Marshall Creek Rd.
Roanoke, TX 76262
(214) 207-7355

 

     
 

Copyright © Skytower Props, Inc.2024